Tachosoft Mileage Calculator V23.1 is the latest mileage counter calculation software, it not only can calculate mileage, but can provide mileage data in the position of the computer program, be convenient for the user to change yourself. Tachosoft Mileage Calculator V23.1 program provides more than 2500 kinds of car mileage calculation, supports the latest new models.
Ford KM Tool (CAN BUS) can read and write Ford KM, and supports instrument dash num.
Newest Software Version: V2.0
Digimaster 3 Digimaster III Original Odometer Correction Master with 980 Tokens
1. Original Yanhua Brand with High Quality.
2. It is new developed odometer correction master.
3. It support English and Online update.
4. It contains the advanced technology of programming new keys for BMW and Benz, CAS-BDM reading/writing and resetting.
The software together with interface is designed for changing the state of kilometers in engine controllers EDC16 in OPEL cars. Everything takes place through diagnostic plug. The software is enriched in the possibility of changing dashboard in selected models.
Tacho Universal V2008.01 Update & Repair Kit can repair the following troubles: Screen display: Diga update and reset, No display after powered on, No vehicle list, screen display black strip, Frequently Halting. Screen display both the following: update handheld and the machine cannot read EEPROM.
We supply this tool with unlimited technical service, high quality, wholesale price and one year warranty.
CAS3/912X/9S12X in Circuit Programmer works with Motorola/Freescale's HC12, HCS12, HCS12X secured microcontrollers! It connects to PC by USB. You needn't remove the micro from the board, just connect 7 pins will be ok.
Audi VW micronas and Fujitsu programmer 2.0 replaces the R200 and R250 fully function.
CAS BDM Programmer used to read and program BMW CAS 1/2/3/3+/4, and BENZ series EIS CPU data. CAS BDM Programmer works together with Digimaster 3, CKM100 or CKM200.
Note: this cas bdm programmer doesn't support 5m48h chip.
NEC Programmer is a Dash Programmer or ECU Flasher designed for Vehicles using the NEC MCU such as Citroen,Peugeot, Hyundai, Honda, Suzuki, Renault, Opel, Alfa, Chevrolet (please refer to the Applicable Models below) that allows you to modify/reprogram your car’s computer or correct the odometer reading.
The tms370 is the lowest cost programmer for TI TMS micro controller development, car radios and car dashboards programming.
Ford OBD2 Tool is a newly released lightweight and friendly OBD device. It is used to mainly perform Ford instrument calibration and immobilizer key matching.
TMS370 Programmer is mainly used for car radio decoding, car odometer adjusting and IMMO Pin code reading.
Fiat KM tool is a mileage programmer for Fiat, if program Fiat KM via OBD2.
BMW CAS4 CAN-filter is a special module which allows to adjust mileage readings in BMW F01, F07, F10 and X3 2011-2012 (with Motorola processor 9S12 XEP mask 5M48H / 4M48H – SC 66 7095 CAG). The newest version is V5.
Mazda OBD2 Odometer correct and Airbag module repair tool, especially for Mazda vehicle from 2005-2015.
It is OBD2 user friendly tool, used for calibrate odometer and airbag repair.
PSA BSI tool V1.2 professional odometer tool supports Peugeot Citroen till 2008 by OBD2, no need open dashboard. PSA BSI tool is used to read and write eeprom of BSI, programming new KM in BSI and more.
VAG KM+IMMO tool by OBD2 can program Volkswagen ,seat and Skoda cars from year 2006.06 by OBDII diagnostic. You can do odometer correction, PIN code read, EEPROM read/write with VAG KM+IMMO tool by OBD2.
BMW M35080 corrects mileage for BMW odometers with M35080 chip. BMW M35080 can support BMW E65 / E38/ E39/ E46, etc. The software version is 3.0.
VW & AUDI 250 Programmer is mainly used for programming CDC 32X7CPU which produced by Micronas company.